Side-Power SE 60/185 S Bedienungsanleitung PDF herunterladen (Seite 9)

SE 60/185S ignition protected thruster assembly 1.0 - 2007

• Explanation of electrical table

- All cable lengths are the total of + and - (to and from).

- Battery size is stated as minimum cold crank capacity, not Ah.

- Use slow fuse rated to hold stated Amp-Draw for min. 5 minutes.

* Cable size and main battery size when an extra bow battery with minimum the CCA mentioned as A is installed.

• It is important that you use a good cable size and batteries with a high cranking capacity to feed the thruster, because it is the actual

voltage at the motor while running the thruster that decides the output rpm of the motor and thereby the actual thrust. Please see the

list below for advised min. sizes of cables and batteries. You can of course use larger cables for even better results.

• A main switch (*C) that can take the load without noticable voltage drop must be installed in the main positive lead so the power

for the thruster can be turned off independently of the rest of the system when not on board or in emergencies. This should be placed

in an easily accessible place and the boats instructions should include information that this should be turned off like the other main

switches of the boat.

• We also advice to install a fuse (*D) in the positive lead for protection agains short circuiting of the main cables. This fuse should be

of a adequate quality which normally means that it is physically large as these have less voltage drop than the simple / small ones. It

should be of the slow type and sized to take the amperage draw for atleast 5 minutes.

• Remember to use ignition protected fuses and switches if tted in areas that require this feature.

• A circuit breaker can be used instead of the fuse and main power switch as long as the functionality is the same.

• The cable ends must be tted with terminals and these must be well isolated against contact with anything but the proper connection

point.

• If the main switch and fuse are installed in the same gas area they also have to be ignition protected.

• The negative / minus cable connects to the (-) terminal. Bolt M10. Tighten with 25 Nm / 18,43 lb/ft.

• The positive / plus cable connects to the "+" terminal. Bolt M10. Tighten with 25 Nm / 18,43 lb/ft.

Electrical installation

Model Voltage Nominal

current

draw

Min. battery

CCA

>7m total + & - 7-14m total + & - 15-21m total + & - 22-28m total + & - 28-35m total + & - 36-45m total + & -

Min. Rec. Min. Rec. Min. Rec. Min. Rec. Min. Rec. Min. Rec.

SE60/185S 12 V 340 A DIN: 350

SAE:665

AWG

1/0

2/0

3/0

2x 70

2x 2/0

120

4/0

2x95

2x 3/0

2x 95

2x 3/0

2x120

2x 4/0

2x120

2x 4/0

280*

24 V 170 A DIN: 175

SAE: 332

AWG

1/0

2/0

Battery & cable recommendations:

Minimum and recommended cable dimensions can be identical due to safety margins and cable heat considerations for short cable lenghts.

* Minimum or recommended cable cross section in mm

SP55S2i ignition protected thruster assembly

1.1 - 2006

• Explanation of electrical table

- All cable lengths are the total of + and - (to and from).

- Battery size is stated as minimum cold crank capacity, not Ah.

- Use slow fuse rated to hold stated Amp-Draw for min. 5 minutes.

* Cable size and main battery size when an extra bow battery with minimum the CCA mentioned as A is installed.

• It is important that you use a good cable size and batteries with a high cranking capacity to feed the thruster, because it is the actual

voltage at the motor while running the thruster that decides the output rpm of the motor and thereby the actual thrust. Please see the list

below for advised min. sizes of cables and batteries. You can of course use larger cables for even better results.

• A main switch (*C) that can take the load without noticable voltage drop must be installed in the main positive lead so the power for the

thruster can be turned off independently of the rest of the system when not on board or in emergencies. This should be placed in an easily

accessible place and the boats instructions should include information that this should be turned off like the other main switches of the boat.

• We also advice to install a fuse (*D) in the positive lead for protection agains short circuiting of the main cables. This fuse should be of a

adequate quality which normally means that it is physically large as these have less voltage drop than the simple / small ones. It should

be of the slow type and sized to take the amperage draw for atleast 5 minutes.

• Remember to use ignition protected fuses and switches if fitted in areas that require this feature.

• A circuit breaker can be used instead of the fuse and main power switch as long as the functionality is the same.

• The cable ends must be fitted with terminals and these must be well isolated against contact with anything but the proper connection point.

• If the main switch and fuse are installed in the same gas area they also have to be ignition protected.

• The negative / minus cable connects to the (-) terminal. Bolt M10. Tighten with 25 Nm / 18,43 lb/ft.

• The positive / plus cable connects to the "+" terminal. Bolt M10. Tighten with 25 Nm / 18,43 lb/ft.

Electrical installation

Battery

12V or 24V

Counter Nut

Nut

Washer

Cable terminal

Washer

Counter Nut

Nut

Washer

35 mm2 60 mm2 95 mm2 95 mm2 120 mm2 120 mm2

AWG 1 AWG OO AWG OOO AWG OOOO AWG OOOO

2 x AWG OOOO

25 mm2 25 mm2 35 mm2 35 mm2 50 mm2 50 mm2

AWG 4 AWG 4 AWG 2 AWG 2 AWG 1 AWG 1

Min.Battery

CCA by Din

200 CCA Din

380 CCA SAE

200 CCA Din

380 CCA SA E

200 CCA Din

380 CCA SAE

250 CCA Din

475 CCA SAE

200 CCA Din

380 CCA SAE

400 CCA Din

760 CCA SAE

350 CCA Din

665 CCA SA E

Min.Battery

CCA by Din

12 V

330 A Din

627 A SAE

350 CCA Din

665 CCA SAE

24 V

160 A Din

304 A SAE

200 CCA Din

380 CCA SAE

SP55S2i

Min. Cable

dim ension

Min.Battery

CCA by Din

350 CCA Din

665 CCA SAE

400 CCA Din

760 CCA SAE

400 CCA Din

760 CCA SAE

Min.Battery

CCA by DIN

Min. Cable

dim e nsion

Min. Cable

dim ens ion

Min.Battery

CCA by DIN

16 - 19m total

20 - 23m total

24 - 27m total

Mode l Voltage

Current

draw

Min. Cable

dim ens ion

Min.Battery

CCA by DIN

Min. Cable

dim ension

Min. Cable

dim ension

Table for selection of main cable,

battery, fuse and main-switch

sizes.

up to 7m total

8 - 11m total

12 - 15m total

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Side-Power SE 60/185 S Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern