Side-Power SX80/185T Installationshandbuch PDF herunterladen (Seite 8)

REMOTE INSTALLATION OF THE ELECTRONIC BOX.

As the electronic controlbox and its contact are the most sensitive parts on the thruster, we advice that these are

removed from the thruster and fitted in a high place in the boat so to secure these from water ingress, even if the

thrusters compartment gets flooded.

Included with the stern-thruster tunnel kit is an extension cable that will allow you to do this.

Procedure:

1 Exchange the GREY and BLUE wires on the sides of the main solenoids that is coming from the

electronic controlbox with the GREY and BLUE wires from the extension cable.

2. Exchange the BLACK, BROWN and WHITE wires from the electronic controlbox with BLACK ,

BROWN and WHITE wires in the extension cable.

3. Cut the strips holding the RED internal connections together with the other internal connections,

and leave the RED wires on the main solenoids. Cut the red wire in accordance to drawing.

4 Remove the electronic controlbox and its harness from the solenoid system on the thruster.

5 Locate and fasten the electronic controlbox in a position where it will surely keep dry. This should

be relatively high in the boat, so that even an extreme level of bilge water can not get to it. Also

ensure that the position is safe against water running from above.

6 Remove the electronic controlbox from its original harness and plug it into the connector on the

extension cable.

7. The extension cable to the control panel(s) must now be connecte to the AMP male plug on this

remotely installed controlbox. Ensure that all controlcable junctions/connectors are placed so that

they will stay dry at all times.

Wet bilge area

SID E-PO WER

Electronic controlbox

placed high, away from

splashing water.

SIDE-POWER

Ref # 6 1230

Sleipner Motor AS

N-1612 Fredrikstad

Electronicinterfacefor thrustermotor controls

Connectors to

thruster

extension

Electronic

controlbox to

be removed

from thruster

New

connector for

electronic

controlbox

AMP male

connector to

control panel(s)

Stern thruster installation manual Version 1.6 - 2005

EXISTING HARNESS

REMOVED

Red

Existing

Red

(after

cutting)

EXISTING HARNESS

SI D E- P OW ER

R ef # 6 123 0

S le ipn er M ot orA S

N - 1612 F re dri kst ad

Elec tr o ni c inter fac e for thr u st er m ot o r co n tr o ls

Red

Black

Grey

Blue

Brown

White

Cut the

Red wire

as close as

possible to

contact

Bolt

New Grey

STERN EXTENSION

HARNESS INSTALLED

Red

New Red

New Blue

New Black

S ID E- P O W E R

R e f # 6 1 230

Slei pn er M ot or AS

N- 1 612 Fr ed ri k st a d

Elec tr o nic i n ter fac e f or thr u st er mot o r co n t ro l s

New White

New Brown

ELECTRICAL INSTALLATION OF STERNTHRUSTER SYSTEMS

PS ! This is additional information especially for sternthruster installations, and the installation

manual for the thruster you are installing must be used complementary.

Stern thruster installation manual Version 1.6 - 2005

If a bow thruster is also installed, we strongly advice to use seperate battery banks for the two

thrusters to avoid extreme voltage drop if both thrusters were to be used at the same time, and to

ensure maximum performance.

Battery banks must have common minus!

Refer to the thruster manuals for advised battery capacity and cable sizes for each thruster.

If a single control panel other than Sidepower’s is to be used for both bow and stern thruster,

be sure it has a single positive connection from only one of the two thrusters to avoid current

leakage between the two battery banks. If you are installing the standard Sidepower dual

joystick panel this is already taken care of.

Wiring diagram for installation with original Sidepower dual joystick panel.

SLEIPNER

SIDEPOWER

THRUSTERS

OFFO N ON

BOW

STERN

To sternthruster

To bowthruster

grey

blue

black

grey

blue

red

ON / OFF

System

Control

light

Joystick

for stern-

thruster

Joystick

for bow-

thruster

Positive lead from

sternthruster has been

removed in panel to

avoid current leakage

between

battery banks if the

thrusters are powered

by different battery

banks.

Wiring diagram (simplified) for dual joystick panel

Visual connection diagram for dual joystick panel



When using the original Sidepower control cables just connect them

to the corresponding joystick



There are no plus/positive power connected from the sternthruster

BOWSTERN

black

Version 1.7.1 - 2010

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Side-Power SX80/185T Installationshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Side-Power SX80/185T