Side-Power SP 125 T Installationshandbuch PDF herunterladen (Seite 8)

Stern tunnel installation version 1.7.2 - 2015

REMOTE INSTALLATION OF THE ELECTRONIC BOX.

As the electronic controlbox and its contact are the most sensitive parts on the thruster, we advice that these are

removed from the thruster and fitted in a high place in the boat so to secure these from water ingress, even if the

thrusters compartment gets flooded.

Included with the stern-thruster tunnel kit is an extension cable that will allow you to do this.

Procedure:

1 Exchange the GREY and BLUE wires on the sides of the main solenoids that is coming from the

electronic controlbox with the GREY and BLUE wires from the extension cable.

2. Exchange the BLACK, BROWN and WHITE wires from the electronic controlbox with BLACK ,

BROWN and WHITE wires in the extension cable.

3. Cut the strips holding the RED internal connections together with the other internal connections,

and leave the RED wires on the main solenoids. Cut the red wire in accordance to drawing.

4 Remove the electronic controlbox and its harness from the solenoid system on the thruster.

5 Locate and fasten the electronic controlbox in a position where it will surely keep dry. This should

be relatively high in the boat, so that even an extreme level of bilge water can not get to it. Also

ensure that the position is safe against water running from above.

6 Remove the electronic controlbox from its original harness and plug it into the connector on the

extension cable.

7. The extension cable to the control panel(s) must now be connecte to the AMP male plug on this

remotely installed controlbox. Ensure that all controlcable junctions/connectors are placed so that

they will stay dry at all times.

Wet bilge area

SIDE-POWER

Electronic controlbox

placed high, away from

splashing water.

SIDE-POWER

Ref #6 1230

Sleipner Motor AS

N-1612 Fredrikstad

Electronicinterface for thr ustermotor controls

Connectors to

thruster

extension

Electronic

controlbox to

be removed

from thruster

New

connector for

electronic

controlbox

AMP male

connector to

control panel (s)

Stern thruster installation manual Version 1.6 - 2005

EXISTING HARNESS

REMOVED

Red

Existing

Red

(after

cutting)

EXISTING HARNESS

SI DE- POWER

R ef # 6 123 0

S le ipn er M otor A S

N - 1612 F re dri k st ad

Elec tr oni cinter fac e for thr u st er m ot o r co n tro ls

Red

Black

Grey

Blue

Brown

White

Cut the

Red wire

as close as

possible to

contact

Bolt

New Grey

STERN EXTENSION

HARNESS INSTALLED

Red

New Red

New Blue

New Black

S ID E- P O W E R

R e f # 6 1 230

Slei pn er Mot or AS

N- 1 612 Fred ri kst a d

Elec tr on ic i n ter fac e f o r thr u st e r mo t o r cont rol s

New White

New Brown

Remote installation of the electronic box

As the electronic controlbox and its contact are the most sensitive parts on the thruster, we advice that these are

removedfromthethrusterandttedinahighplaceintheboattosecurethesefromwateringress,evenifthe

thrustercompartmentgetsooded.Includedwiththestern-thrustertunnelkitisanextensioncablethatwillallow

you to do this.

Procedure:

1. Exchange the GREY and BLUE wires on the sides of the main solenoids that is coming from the electronic con-

trolbox with the GREY and BLUE wires from the extension cable.

2.ExchangetheBLACK,BROWNandWHITEwiresfromtheelectroniccontrolboxwithBLACK,BROWNandWHITE

wires in the extension cable.

3.CutthestripsholdingtheREDinternalconnectionstogetherwiththeotherinternalconnections,andleavethe

REDwiresonthemainsolenoids.Cuttheredwireinaccordancetodrawingbelow.

4. Remove the electronic controlbox and its harness from the solenoid system on the thruster.

5. Locate and fasten the electronic controlbox in a position where it will surely keep dry. This should be relatively

high in the boat, so that even an extreme level of bilge water can not get to it. Also ensure that the position is safe

against water running from above.

6. Remove the electronic controlbox from its original harness and plug it into the connector on the extension cable.

7.The extension cable to the control panel(s) must now be connecte to the AMP male plug on this remotely in-

stalled controlbox. Ensure that all control cable junctions/connectors are placed so they will stay dry at all times.

Electronic control-

box placed high, away

from splashing water

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Side-Power SP 125 T Installationshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Side-Power SP 125 T